Vantec UGT-ST320R - SATA 150 PCI Combo Host Card driver and firmware
Related Vantec UGT-ST320R Manual Pages
Download the free PDF manual for Vantec UGT-ST320R and other Vantec manuals at ManualOwl.com
Flyer - Page 1
...to update any computer system.
Specifiactions:
Model: Ports:
Interface: Dimensions:
UGT-ST320R 2 External eSATA Port 2 Internal SATA 150 Ports PCI 122mm x 120mm x 22mm
System Requirement
Computer With Available PCI Slot Windows® 2000/XP/2003/Vista/7 (32/64 bit) (CD-Rom Drive May Be Needed For Drivers)
Package Contents
Vantec 4-Port SATA 150 PCI Combo Host Card w/RAID,SATA Cables,Drive CD...
User Guide - Page 2
...Image SiI3512 SATA controller chip z Compliant with PCI Specification, Rev. 2.3 z Compliant with Serial ATA 1.0 specification z Provides two independent channels to support up to two Serial
ATA drives z Supports RAID0(striping) and RAID1(mirroring) for speed and
data protection respectively z HDDs function normally when not in RAID sets z Supports SATA up to 150MB/Sec z Supports Windows® 2000...
User Guide - Page 3
Package Contents
z Vantec 4-Port SATA 150 PCI Combo Host Card w/RAID x 1 z SATA Cables x 2 z Installation Guide x 1 z Driver CD x 1
*User's Manual Is on Driver CD
Hardware Description
Note: There are four SATA ports in SATA 150 PCI RAID Card 2-Channel. We name these ports from A to D. Ports A & B are internal SATA ports. Ports C & D are external SATA ports. Changing the jumper setting allows you ...
User Guide - Page 5
... install the card, carefully align the card's bus connector with
the selected PCI slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 6. Replace the slot bracket's holding screw to secure the card.
Device Connection
The Vantec 4-Port SATA 150 PCI Combo Host Card w/RAID is a two channel Serial ATA controller that supports up to two Serial ATA hard disk drives...
User Guide - Page 7
... when prompted to enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter. 3. Select Striped, then press Enter. 4. Select Manual configuration then press Enter 5. Select the first drive, press Enter. 6. Select the second drive, press Enter. 7. Select chunk size from 4k, 8k, 16k, 32k, 64k or 128k, then press
Enter.
UGT‐ST320R
Page 7
User Guide - Page 8
...installing a conventional hard drive.
RAID 1 (Mirror) For New/Blank Hard Drives
1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS.
2. At the next screen select Create RAID Set... the BIOS. 7. When asked Are you sure to exit(Y/N)?, press Y to exit and
reboot. 8. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
UGT‐ST320R
Page...
User Guide - Page 9
... to enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press Enter. 3. At the next screen select Mirrored then press Enter. 4. Select Manual configuration, then press Enter. 5. Select the Source drive, press Enter. 6. Select the Target drive, press Enter. 7. Enable Disk Copy, select Yes, then press Enter. Note: Enable Disk Copy - Copy current content of source driver to mirror...
User Guide - Page 10
... the SATARAID GUI while in Windows. The steps below will guide you in rebuilding a failed mirror set. 1. Replace the failed drive with one of equal or greater capacity, then
start the computer. 2. During boot press Ctrl+S or F4 to enter the RAID BIOS. 3. Select Rebuild Mirrored Set then press Enter. 4. Select the desired set and then press Enter. 5. When...
User Guide - Page 11
... disk.
Low Level Format
Low Level Format is build into the RAID BIOS to make it more convenient to erase the entire contents of a hard disk drive, including data, drive and partition information. The Low Level Format utility works on single hard drive only, before the RAID set is configured.
BIOS Configuration
The Serial ATA 2-Channel RAID adapter BIOS will appear every time
UGT‐ST320R...
User Guide - Page 12
... the devices attached to it.
Driver Installation
For Windows® 2000
For New Installation
A new installation requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the "UGT-ST320R\XP_2003_Vista_2008 32-bit" folder, found on the
driver CD, onto a blank floppy disk then follow the directions below. 1. Setup the RAID Array prior to Windows installation...
User Guide - Page 13
... for a suitable driver for my device (recommend)
then click Next. 4. Insert the driver CD, check CD-ROM drives, uncheck the other
boxes, click Next, then click Next again. 5. Click Finish.
For Windows® XP/Server 2003
For New Installation
A new installation requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the "UGT-ST320R\XP_2003_Vista_2008 32...
User Guide - Page 14
... 1. Setup the RAID Array prior to driver installation and boot up to
Windows. 2. At the Found New Hardware Wizard, select No, not this time,
then click Next. 3. Insert the driver CD, select Install the software automatically
(Recommended), and click Next. 4. Click Finish 5. Restart Windows to complete the installation.
For Windows®XP-x64/Server 2003-x64
For New Installation
UGT‐ST320R...
User Guide - Page 15
... a floppy disk for the driver installation. To make this floppy disk, copy the contents of the UGT-ST320R\XP_2003_Vista_2008 64-bit" folder, found
on the driver CD, onto a blank floppy disk then follow the directions below. 1. Setup the RAID Array prior to Windows installation. 2. Follow Microsoft's Windows installation procedure. 3. At the Windows Setup screen, press F6 to install the RAID driver...
User Guide - Page 16
... Windows® 7
For New Installation 1. Setup the RAID Array prior to Windows installation. 2. At the Windows Setup screen, press Load Driver to install the
driver. 3. Insert the CD driver into your CD-ROM Drive, please select
Silicon Image SiI 3512 SATARaid Controller (D:\UGT-ST320R\Win7 32-bit), then press Next. (Change D:\ to match your CD-ROM drive letter) 4. Follow the on-screen instructions...
User Guide - Page 17
...the driver CD into the computer's optical drive, type D:\ UGT-ST420R\Win7 32-bit ( substitute whatever drive letter is appopriate), and then click Next. 5. When the next window appears, click Close to complete the installation.
For Windows® 7-x64
For New Installation 1. Setup the RAID Array prior to Windows installation. 2. At the Windows Setup screen, press Load Driver to install the
driver...
User Guide - Page 18
...click on the next to other device to expacnd the list. Right-click"RAID Controller" and select Updated Driver Software... 3. When the Update Driver Software appears, select "Browse my computer for driver software" 4. When the next window appears, insert the driver CD into the computer's optical drive, type D:\ UGT-ST420R\Win7 32-bit ( substitute whatever drive letter is appopriate), and then click...
User Guide - Page 19
...SiI 3512 SATARaid Controller should be displayed Windows® Vista/7: Double click Storage controllers: -Silicon Image SiI 3512 SATARaid Controller should be displayed
SATARAID Management Software Installation
1. Please insert the CD driver bound with SATA 150 PCI RAID card into your CD-ROM Drive.
2. At the Windows desktop click Start, then Run. 3. Type D:\UGT-ST320R\SATARAID Tool\setup.exe,then...