Vantec UGT-PCE430-4C - Quad Chip Dedicated 5Gbps USB 3.0 PCIe Host Card driver and firmware
Related Vantec UGT-PCE430-4C Manual Pages
Download the free PDF manual for Vantec UGT-PCE430-4C and other Vantec manuals at ManualOwl.com
User Guide - Page 2
Contents:
Contents 2 Chapter 1: Introduction 3 1.1 Features 3 1.2 System Requirements 4 1.3 Package Contents 4 Chapter 2: Getting Started 5 2.1 Hardware Installation 5 2.2 Driver Installation 6 2.3 To verify the Hardware device 8 2.4 To Uninstall Drivers 9 Chapter 3: Troubleshooting Tips 10
UGT-PCE430-2C/4C
Page 2
User Guide - Page 4
... and Low Profile bracket for easy installation into standard or small form factor system
1.2 System Requirements
Windows XP, Vista, 7, 8, 8.1 (32/64 bit), Server 2003, 2008 R2, 2012, Linux 2.6.31 or later
PCI Express x4, x8 or x16 slots
1.3 Package Contents
1 x Dual/Quad Chip 4-Port Dedicated 5Gbps USB 3.0 PCIe Host Card.
1 x Driver CD
UGT-PCE430-2C/4C
Page 4
User Guide - Page 5
... and secure the screws back on the card.
3. Turn off the power to your computer, unplug the power cord and remove the cover of the computer system.
4. Remove the slot bracket from an available PCI-Express x4 (x8, x16) slot.
5. To install the card, carefully align the card's bus connector with the selected PCIe slot on the motherboard. Push the
UGT-PCE430-2C/4C
Page 5
User Guide - Page 6
... is powered ON, proceed with the
installing the necessary drivers. NOTE: If you are using Windows 8 or 8.1, your system will automatically detect the device and install the necessary drivers for you. You do not have to use the CD to start the manual installation process.
2.2 Driver Installation
1. Insert the provided CD into your disk drive. Browse to the folder "UGT-PCE430-2C_4C" for the setup...
User Guide - Page 7
*Note: Actual image may varies 3. When the installation is done, select "Finish".
4. Your device is now ready for use. UGT-PCE430-2C/4C
Page 7
User Guide - Page 8
2.3 To verify the Hardware device
1. Click on the "Device Manager" tab in the Windows Control Panel.
Start > Control Panel > Device Manager
2. Double click on the "Universal Serial Bus controllers" device and it will expand the subset showing "Renesas Electronics USB 3.0 Host Controller" and "Renesas Electronics USB 3.0 Root Hub" in the Device Manager.
UGT-PCE430-2C/4C
Page 8
User Guide - Page 9
2.4 To Uninstall Drivers
1. Click on the "Programs and Features" tab in the Windows Control Panel.
Start > Control Panel > Programs and Features
2. Entry "Uninstall or change a program" page, and double click "Renesas Electronics USB 3.0 Host Controller Driver" to process driver uninstallation procedure.
UGT-PCE430-2C/4C
Page 9
User Guide - Page 10
... restart the computer. If the computer starts successfully, it means that the card has not been inserted into the PCI Express slot correctly. Please clean slot contact with a dry cloth and try another PCIe x4 slot. This PCIe x4 card will also fit into the PCIe x8 or x16 slot.
Getting a yellow exclamation point on controller
UGT-PCE430-2C/4C
Page...
User Guide - Page 11
...
A message is displayed stating that not enough power can be given to the connected device. Make sure to plug 4-pin power cable on board to provide enough power to USB devices.
Is it possible to connect current USB 1.1 or 2.0 devices to the USB 3.0 PCI Express card? Yes it will work. Device will not be running at USB 3.0 speed, but at USB 2.0/1.1 speed.
UGT-PCE430-2C/4C
Page 11