TRENDnet TW-200 driver and firmware
Related TRENDnet TW-200 Manual Pages
Download the free PDF manual for TRENDnet TW-200 and other TRENDnet manuals at ManualOwl.com
Manual - Page 8
Port Configuration 29 Advanced Setup 34 Status Screen 35 E-Mail Configuration 38
5 OPERATION 41 IP Address Configuration 41 PC Address Configuration 41 Router Address Configuration 44 Internet Access 45 E-Mail Configuration 46 Sharing E-Mail Example 47
A TROUBLESHOOTING 50
B LOG MESSAGES 54
C AT COMMANDS 58 Required Settings 58 Finding the current Initial String 60 AT Commands 62 ...
Manual - Page 9
... your network access to the vast resources available on the Internet. Once the Error! Reference source not found. is installed and configured, the Internet is just a click away.
Figure 1: Office to Internet
Error! Reference source not found. Features
Once configured, the Error! Reference source not found. is able to use your modem(s) to connect to your ISP (Internet Service Provider). The Error...
Manual - Page 10
... Internet Service Provider.
• DHCP Server Support. Dynamic Host Configuration Protocol provides a dynamic IP address to PCs and other devices upon request. The Error! Reference source not found. can act as a DHCP Server.
• Easy Setup. Either a communications program and direct cable connection; or a WEB browser, can be used.
• Configuration Security Features. Optional password...
Manual - Page 17
...
• Ethernet Network employing 10BaseT or 10Base2 cable and the TCP/IP protocol.
• An external modem or ISDN TA (Terminal Adapter). • Configuration serial cable for Terminal mode configura-
tion (supplied). • Single user account with a local ISP.
Procedure
The installation choices are as follows.
Configure, then Install
Configuration is done using a serial cable connection...
Manual - Page 18
...your existing Ethernet LAN is quick and easy. Simply follow the instructions below:
1. Choose an Installation Site
Select a place on the network to install the Error! Reference source not found.. Remember that you need phone jacks and power outlets near your chosen location.
2. Connect Network Cable
The Error! Reference source not found. supports two types of network cables: Thin Ethernet (10Base2...
Manual - Page 19
... from the hub to the device is 100 meters.
Warning: Do not attempt to connect more than one type of cable at the same time or change the network cable while the Error! Reference source not found. is powered On.
3. Connect Modem & Phone Line
Connect the modem, using a standard serial cable, to the Error! Reference source not found.'s serial port. Next, connect a telephone line...
Manual - Page 21
Installation This page was deliberately left blank.
13
Manual - Page 31
... existing
WEB browser. This uses the LAN connection, so the device must be installed on the LAN first.
Terminal Mode Configuration
Procedure
1. With the power Off, use the supplied serial cable to connect your PC to the serial port on the Error! Reference source not found.. For multi-port models, you MUST use Port 1.
2. Set both of the Error! Reference source not found.'s dip...
Manual - Page 32
... found. User Guide
Setting Terminal Emulation Baud Rate Data Bits Parity Stop Bits Flow Control
Value VT100 mode 19200bps 8-bit no parity 1 stop bit Xon/Xoff OR None
4. Start the configuration program by connecting the power to the Error! Reference source not found.. If nothing appears on your screen, press ESC.
5. Configure the Error! Reference source...
Manual - Page 38
... support tables and forms. The Error! Reference source not found. must be installed on your LAN first.
Connection
To establish a connection from your PC to the device: • Start your WEB browser • In the Address box, enter "HTTP://" and the IP Address of
the Error! Reference source not found., as in the following example:
HTTP://192.168.0.1
Password...
Manual - Page 43
... information.
• Hang Up will hang up the modem, breaking an existing connection.
• Dial will establish a connection to the ISP, if no connection currently exists.
• Clear Log will remove any data shown in the Log window.
• Refresh will update the information shown on screen.
You must click OK to have...
Manual - Page 45
Status Screen
Configuration Programs
The Status screen can be reached with the hyperlink on the navigation bar. The following example is for the 4-port model.
Figure 10: Status Screen
No. of Ports Firmware Version
The number of serial ports on this device.
Version of the firmware (embedded software, including this program) which is currently installed. Techni-
37
Manual - Page 51
5 Operation
IP Address Configuration
Once the Error! Reference source not found. has been configured and installed in your network, it is ready for use. However, the PCs on your network must be configured correctly. If you have a router, it also needs to be configured correctly.
PC Address Configuration
The following TCP/IP settings should be checked. • IP Address •...
Manual - Page 53
...3. Click on the radio button to obtain an IP address automati-
cally, as shown above. Default Gateway Address
This should be left blank. The DHCP server will provide... Disabled IP Address
Each workstation must have a unique IP address. There should be no need to change any existing addresses. Default Gateway Address This value will depend on whether or not you have a router installed on your LAN.
45
Manual - Page 60
... for further advice.
Problem 1: Solution 1:
I configured and installed the Error! Reference source not found. in the network, but I can't get it to respond.
If the configuration settings are correct, then you probably forgot to set the dip switches back to their Off positions after configuration. Power Off the Error! Reference source not found. and ensure that the...
Manual - Page 62
... it is not transparent. Some programs may have limited functionality when used with the Error! Reference source not found..
The number of supported applications is being expanded as rapidly as possible. The following applications and protocols are supported by firmware V5.0:
Telnet, FTP, HTTP, ping
POP/SMTP, Archie, NNTP
TFTP, IRC, Gopher
DNS, SNMP...
Manual - Page 64
... appear in the Log window of the HTML application. More information on error messages is contained after the table.
Message
Description
Dial on demand
Dialing the ISP ("Dial on demand" setting is ON).
Try to establish
The device is trying to connect with
physical connection. the ISP, using the modem.
Busy error
The number dialed was...
Manual - Page 71
...Set 4. Select Advanced to see the screen below.
Figure 17:- Advanced Connection (W95) 5. Check the option Record a log file. Then click OK and
exit. 6. Use Dial-up Networking to make your on-line connection
normally. A log file MODEMLOG.TXT will be created in your Windows...(Note: The Win 95 Dial-up Networking scripting language is more complex than that of the Error! Reference source not found..)
63
Manual - Page 76
...
Data rate, terminal-to-modem DTE/DCE rate fixed at DTE setting Carrier Detect operations Carrier Detect tracks presence of carrier Data Terminal Ready (DTR) operations DTR off causes modem to hang up Load the default factory settings, Data flow control, DTE/DCE, n=0,3,4 Flow control disabled Hardware (RTS/CTS) flow control Software (XON/XOFF) flow control Data Set Ready (DSR) DSR...
Manual - Page 82
... for use with the Error! Reference source not found., the procedure is as follows. 1. Click and follow the selection
Start Menu-Programs-Accessories-HyperTerminal. 2. Start the HyperTerminal Program. 3. You should now be prompted for New connection. Enter
Null Modem as the name. (A Null Modem is a direct connection using a Null Modem cable.) 4. Select an icon to...