TRENDnet TEW-410APB driver and firmware
Drivers and firmware downloads for this TRENDnet item
Related TRENDnet TEW-410APB Manual Pages
Download the free PDF manual for TRENDnet TEW-410APB and other TRENDnet manuals at ManualOwl.com
Data Sheet - Page 1
... to Ethernet network at anytime to add wireless users on the network. Save time, labor, and material for network cable installation.
Flexible: Works as Access Point, Access Point Bridge, Access Point Client, or Wireless Repeater.
Security: Provides 64/128-bit WEP Encryption and MAC Address Access Control.
Cost Effective: One unit provides multiple wireless connections to wired LAN.
TEW-410APB (07...
Data Sheet - Page 2
...• FCC, CE
NETWORKING SOLUTIONS
PRODUCT INFORMATION
TEW-401PC: 54Mbps 802.11g Wireless PC Card TEW-403PI: 54Mbps Wireless PCI Network Adapter TEW-410APB: 54Mbps Wireless Access Point + Bridge + Repeater TEW-411BRP: 54Mbps Wireless Broadband Router + Access Point TEW-PS3: 3-port Wireless Ethernet Print Server TEW-PS1U: 11Mbps Wireless USB port Multi-Protocol Print Server TEW-IA04O: 4dBi Omni...
Manual - Page 3
Contents 1. Introduction...3 2. Safety Notification 4 3. Hardware Installation 5 4 Web Management Settings 6
4.1. Primary Setup ...7 4.2. System...11 4.3. Operating Mode...12 4.4. Status...14 4.5 Traffic Log...15 4.6 AccessControl ...16 4.7 Advanced Wireless...17 4.8. SNMP...19 4.9. Upgrade Firmware...20
5. Troubleshooting ...22
User's Guide
2
Manual - Page 4
1. Introduction
Thank you for purchasing your AP Wireless 802.11g AP. This user guide will assist you with the installation procedure. The package you have received should contain the following items:
AP Wireless 802.11g AP User Guide Power Supply / Cord Ethernet Cable
Note: if anything is missing, please contact your vendor
User's Guide
3
Manual - Page 5
...Please read the user manual thoroughly before you install the device. The device should only be repaired by ...device should be placed in a sheltered and non-slip location within a temperature range of +5 to +40 Celsius degree. Please do not expose the device to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
User's Guide...
Manual - Page 6
... power adapter may cause damage to your device and
violate your warranty.
Reset
Press the Reset Button for approximately ten seconds, all configurations will set to factory default settings.
LAN
The RJ-45 Ethernet ports used to connect your PC, hub, switch or Ethernet network.
AP Default Settings
The default settings are shown following.
User
admin
Password
admin
AP IP Address...
Manual - Page 10
...Wireless Adapter's driver, and Wireless Utility can support it, WPA needs 802.1x authentication (when RADIUS mode is chosen), though the Operating System must also support 802.1x protocol. For Microsoft's OS family, only Windows XP has incorporated this by default. The rest of the OS must installed 3er party's client software...WPA Pre-Shared Key, enter a password in the WPA Shared Key field ...Guide
9
Manual - Page 14
... the AP function role and at the same time performing a communication with other 802.11g AP to establish and extend your Wireless Network cover. Please enter the Remote Access Point's MAC address to enable this feature.
Wireless Bridge: This mode allows the connection of one or more remote LANs with a central LAN.
* Click Apply to save your settings.
User's Guide
13
Manual - Page 15
...-flash every 5 seconds to keep most update information.
LAN section will be displaying all information related on AP, such as the IP address and the current configuration type.
Wireless section will be displaying information related on the Wireless interface, such as SSID, Channel, Encryption and statistics of network traffic.
*Click the Refresh button to refresh the AP's status and settings...
Manual - Page 16
... activity logs, select Enable. To keep a permanent record of activity logs as a file on your PC's hard drive, Log viewer software must be used. In the Send Log to field, enter the fixed IP address of the PC running the Log viewer software. The AP will send updated logs to that PC. To see a temporary log...
Manual - Page 17
... show up.
Depend on the filtering propose, it can be selected to Deny or Allow. Fill the client stations MAC list to complete the configuration. The table could store up to 40 different MAC addresses. Please follow the format that it required when an address is input.
* Click Apply to save your settings.
User's Guide
16
Manual - Page 19
... error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor modifications of this value are recommended.
DTIM Interval: This value indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window...
Manual - Page 21
... version has a new feature that you want to use.
Note: When you upgrade the AP's firmware, you may lose its configuration settings, so make sure you write down the AP's settings before you upgrade its firmware.
To upgrade the AP's firmware: 1. Download the firmware upgrade file from the internet. 2. Extract the firmware upgrade file. 3. Click the Firmware Upgrade button. 4. On the Firmware Upgrade...
Manual - Page 22
5. Double-click the firmware upgrade file. 6. Click the Upgrade button, and follow the on-screen instructions. Note: Do not power off the AP or press the Reset button while the firmware is being upgraded.
User's Guide
21
Manual - Page 23
... on the rear of the AP to revert to the default settings.
I can't connect to other computers on my LAN.
Cause: The IP Addresses of the computers are not set correctly. Network cables are not connected properly. Windows network settings are not set correctly.
Resolution: Make sure that each computer has a unique IP Address. And the IP must be in the same subnet as
the...
Manual - Page 24
... I can't access the Wireless AP from a wireless network card
Cause: Out of range. IP Address is not set correctly.
Resolution: Make sure that the Mode, SSID, Channel and encryption settings are set the same on each
wireless adapter. Make sure that your computer is within range and free from any strong electrical devices that may
cause interference. Check your IP Address to make sure...
Quick Installation Guide - Page 8
... Wireless Adapter's driver, and Wireless Utility can support it, WPA needs 802.1x authentication (when RADIUS mode is chosen), though the Operating System must also support 802.1x protocol. For Microsoft's OS family, only Windows XP has incorporated this by default. The rest of the OS must installed 3er party's client
Technical Support
You can find the most recent software...