TRENDnet TEW-211BRP driver and firmware
Drivers and firmware downloads for this TRENDnet item
Related TRENDnet TEW-211BRP Manual Pages
Download the free PDF manual for TRENDnet TEW-211BRP and other TRENDnet manuals at ManualOwl.com
Data Sheet - Page 1
TRENDnet
TEW-211BRP
TRENDware, USA
What's Next in Networking
11Mbps Wireless Broadband Router + Access Point
TRENDnet's TEW-211BRP is your IEEE 802.11b Wireless Access Point, Broadband Router, and 4-Port Fast Ethernet Switch all in one! Share Broadband high-speed Internet connection with Ethernet stations and Wireless clients with just one device! Setting up the unit with the Web Browser ...
Data Sheet - Page 2
...
PRODUCT INFORMATION
TEW-201PC 11Mbps Wireless PCMCIA Network Adapter TEW-202CF:11Mbps Wireless CompactFlash Network Adapter TEW-203PI: 11Mbps Wireless PCI Network Adapter TEW-204UB: 11Mbps Wireless USB Network Adapter TEW-210APB: 11Mbps Wireless Access Point + Bridge TEW-211BRP: 11Mbps Wireless Broadband Router + Access Point TEW-PS3: 3-port Wireless Ethernet Print Server TEW-IA04O: 4.0 dBi...
Manual - Page 3
Introduction
Thank you for purchasing your TEW-211BRP Wireless AP Router This manual will assist you with the installation procedure. The package you have received should contain the following items:
??TEW-211BRP Wireless AP Router ??User's Manual ??Power Adapter
Note: if anything is missing, please contact your vendor
2
Manual - Page 4
... installation guide thoroughly before you install the TEW-211BRP
Wireless AP Router ?? The TEW-211BRP Wireless AP Router should only be repaired by authorized and
qualified personnel. ?? Please do not try to open or repair the TEW-211BRP Wireless AP Router yourself. ?? Do not place the TEW-211BRP Wireless AP Router in a damp or humid location,
i.e. a bathroom. ?? The TEW-211BRP Wireless AP Router...
Manual - Page 5
... the power adapter provided with the Wireless AP router. Use of an unauthorized power adapter may cause damage to your device and violate your warranty.
Modem
Port used to connect an external analog backup modem/ISDN TA.
WAN
The RJ-45 Ethernet port labeled WAN is used to connect your Wireless AP Router to your xDSL or Cable modem.
Reset LAN
Resets the configuration to default settings. The...
Manual - Page 10
...
The Device Name is the same as the Computer Name that was set in the Setup Wizard.
The IP Address is the IP Address assigned to LAN side of your Router. The Private LAN Mac Address the Mac Address assigned to the LAN side of your
Router. The Public WAN (Cable/DSL) Mac Address is the Mac Address assigned to the
WAN port of the Router. This Mac Address may be used by some cable modem...
Manual - Page 14
... name" and "WAN Ethernet MAC address". After changing the settings, click NEXT to continue other network settings.
DSL users: If you are using a PPPoE client to connect to your DSL provider, then place a checkmark on the first box, and enter the user name and password in the appropriate box. Cable modem users: If you are using a cable modem, then place a checkmark...
Manual - Page 15
WIRELESS SETTINGS Here allow user to set Wireless AP Router IP and operation channel. The default value for RF are as followed: 1. ESSID: Wireless, Channel: 6. 2. The encryption panel allows the entry of four keys for 64-bit encryption and one set of
128-bit key according to WEP function select. To be written to the driver and registry, each...
Manual - Page 20
ACCESS CONTROL SETTINGS
This function allow administrator to have access control by enter MAC address of client stations.
19
Manual - Page 21
Enable Grant/Deny Access List, user may just input the MAC address of client stations onto MAC Address table, then click ADD button. To delete a MAC address from the list, just click the checkbox and click Delete . Click ' SUBMIT ' to update the data .
20
Manual - Page 23
DYNAMIC SETTINGS
By default, the Router will not send or receive any routing Internet protocols (RIP) to update the routing table. However, the user can enable the Router to automatically send and receive RIP packets to establish routes for commonly used paths.
22
Manual - Page 25
FILTER SETTINGS
This page is only for MIS administrator only. Enable LAN Site Filter function: Block / Pass. Here allow user to add IP Address Range and Destination Port Range to LAN Side Filter Table. The router will Block/Pass packet according to allocate IP range. Click ADD button after input data. Click SUBMITS to update data. To delete...
Manual - Page 27
...Log: View detection logs. Display Routing Table : Display the routing status of the Router. System Diagnostics: Display current status and connection information. Save Settings: Save router configuration to a file . Load Settings: Restore settings to factory default or from a saved file. Upgrade Firmware : Upgrade the firmware with a latest version. Reset Device : Reboot the Wireless AP Router.
26
Manual - Page 29
... Destination LAN IP Address. Gateway IP Address: The IP Address of the assigned Gateway. Hop Count: The number of hops between the Destination LAN IP Address and the Gateway IP Address. SAVE SETTINGS Save the router 's current configurations to a file. Click on SAVE button, click Save at "File Download" dialogue, enter the desired file name with CFG as extension (i.e. SETUP.CFG...
Manual - Page 31
UPGRADE FIRMWARE Here allow user to upgrade firmware. After choosing upgrade firmware, click START to load settings.
The Upgrade Firmware screen enables you to update the firmware. Updated firmware usually fix problems encountered by users, but may incorporate new features.
Begin by clicking the "Browse..." button to browse your computer to select the updated firmware file. Once the firmware file ...
Manual - Page 33
... use the power adapter provided with your Wireless AP Router. Using any other adapter may damage your Wireless AP Router.
LAN Connection Problems
I can't access my Wireless AP Router.
Cause: ?? The unit is not powered on. ?? There is not a network connection. ?? The computer you are using does not have a compatible IP Address. Resolution: ?? Make sure your Wireless AP Router is powered on. ?? Use...
Manual - Page 34
...'t connect to other computers on my LAN. Cause: ?? The IP Addresses of the computers are not set correctly. ?? Network cables are not connected properly. ?? Windows network settings are not set correctly. Resolution: ?? Make sure that each computer has a unique IP Address. If using DHCP through the
Wireless AP Router, makes sure that each computer is set to "Obtain an IP Address automatically" and...
Manual - Page 37
Data encryption: 64/128-bit WEP and ESSID for Security
LED: Power : Indicate power is ON Status : Indicate Firmware loading under proceeding WAN : Indicate WAN port connection
LAN : Indicate LAN port TX/RX operation WLAN: Indicate Wireless been connected and operation
Power Specifications : DC power supply
Input: DC 100-240, 50-60 H z, 1A Output: 5V DC, 2A converter incl. Physical Dimensions 195mm...