TRENDnet TU-ET100plus driver and firmware
Drivers and firmware downloads for this TRENDnet item
Related TRENDnet TU-ET100plus Manual Pages
Download the free PDF manual for TRENDnet TU-ET100plus and other TRENDnet manuals at ManualOwl.com
Data Sheet - Page 1
.... Simply plug the TU-ET100plus to the computer's USB port, connect a standard twisted pair (RJ-45) network cable to the USB Fast Ethernet adapter, load the driver, and you will be networked within seconds!
TRENDnet
TRENDware, USA
What's Next in Networking
FEATURES
10/100Mbps data rate auto-negotiation Features full-duplex mode that doubles the network connection speed Bus Powered Easy to read...
Data Sheet - Page 2
.../Act
Driver Support: • Windows 98/ME/2000/XP
Dimensions: • 76 x 38 x 22 mm (3 x 1.5 x 0.87 inches)
Weight: • Appr. 50 g (1.75 oz.)
Temperature: • Operating: 0° - 65° C (32° - 149° F)
Humidity: • Operating:10 % to 90 % non-condensing
Certifications: • FCC, CE
PRODUCT INFORMATION
TU-ET100plus USB to 10/100Mbps Fast Ethernet Adapter
TU-ET10 USB...
Manual - Page 2
... undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not...
Manual - Page 3
.../100 Fast Ethernet LAN link. Installation is easy and no external power is required! The network sharing is easier than ever.
Specifications Network standard ?? IEEE 802.3 for 10BaseT ?? IEEE 802.3u for 100BaseTX Data Rate ?? 10/100 Mbps1 ?? Double data transfer rate in full duplex
mode Supported operating systems ?? Windows 98/2000/ME/XP Physical ?? Ports: 1 RJ-45, 1 USB A-Plug...
Manual - Page 5
.... Open the Device Manager tab. If the Universal Serial Bus controller device is found, it means your USB port is installed and enabled. If not, either no USB port is installed or the USB bios is not properly enabled. In this case, consult your computer dealer for USB support.
Getting Hooked Up 1. Locate the USB host port of your system.
Align the USB connector toward the USB host port, push evenly...
Manual - Page 7
SOFTWARE INSTALLATION
Installation for Windows 98 1. Once the device is properly connected to
your comp uter, Windows 98 will automatically detect the new hardware device. Perform the following procedures for installing the device driver.
2. Insert the device driver disk into your floppy drive. When the above figure appears, click Next.
- 5 -
Manual - Page 8
3. The installation program will proceed automatically. Follow the on-screen instruction to finish.
4. When Windows prompts you to restart your computer, click No to make some changes to your network settings.
- 6 -
Manual - Page 10
Adapter is found, it means that your device is properly installed and enabled.
Installation for Windows 2000 1. Once the device is well connected to your
computer, Windows 2000 will automatically detect the new device. Click Next to proceed.
- 8 -
Manual - Page 11
2. Select Search for a suitable driver for my device (recommended) and click Next.
3. Insert the new device driver to the disk drive. Select Floppy disk drives. Click Next.
4. Click Next. Windows will copy all the necessary files to your system.
5. Click Yes to continue.
6. Click Finish to complete the software installation.
- 9 -
Manual - Page 12
7. Go to Start ? Settings ? Control Panel ? Ne twork and Dial-up Connections. Double-click Local Area Connections.
8. When the Network dialog box appears, select USB 10/100 Network Adapter and click Install. Set the appropriate protocols and client for you needs. When completed, click OK.
- 10 -
Manual - Page 13
... the Device Manager tab. If the USB 10/100 Network Adapter is found, it means that your device is properly installed and enabled.
Installation for Windows ME 1. Once the device is well connected to your
computer, Windows ME will automatically detect the new device. Select Specify the location of the driver (Advanced) and click Next. 2. Insert the device driver disk into the floppy disk drive on...
Manual - Page 14
3. Click Next to continue.
4. Click Next. Windows will copy all the necessary files to your system.
- 12 -
Manual - Page 15
5. Click Finish to complete the software installation.
6. When asked if you want to restart your computer, click No to continue the Network configuration.
7. Go to Start ? Settings ? Control Panel. Double-click Network.
8. When the Network dialog box appears, select USB 10/100 Network Adapter and
- 13 -
Manual - Page 16
... device exists in your computer and is enabled, go to Start ? Settings ? Control Panel ? System. Click the Device Manager tab. If the USB 10/100 Network Adapter is found, it means that your device is properly installed and enabled.
Installation for Windows XP 1. Once the device is well connected,
Windows will detect the new device and prompt you to insert the network device driver. Click Install...
Manual - Page 17
2. Insert the device Driver Disk into the floppy disk drive of your system. Select Search removable media (floppy, CDROM...) and click Next.
3. Click Next to continue.
- 15 -
Manual - Page 18
4. Windows will start searching for the appropriate driver for the installation. When the screen appears as below, click Continue Anyway to proceed.
5. Wait for seconds while Windows copies the appropriate driver to your system.
6. Click Finish. The software installation for this network device is now completed.
- 16 -
Manual - Page 20
... Install. Set the appropriate protocols and client for you needs. When completed, click OK. 9. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start ? Control Panel ? System. Click the Device Manager tab. If the USB 10/100 Network Adapter is found, it means that your device...