TRENDnet TEW-410APBplus driver and firmware
Drivers and firmware downloads for this TRENDnet item
Related TRENDnet TEW-410APBplus Manual Pages
Download the free PDF manual for TRENDnet TEW-410APBplus and other TRENDnet manuals at ManualOwl.com
Data Sheet - Page 1
.... With TRENDnet's Wireless Access Point and Wireless Network Adapters, users can connect to Ethernet/Fast Ethernet LAN at home or office to access network resources such as hard drives, CD-ROM/DVD drives, network printers, and Internet connection.
TRENDnet
TRENDware, USA
What's Next in Networking
FEATURES
Uses 2.4 GHz ISM Frequency Band, Wi-Fi Compliant with IEEE 802.11g and IEEE 802.11b Devices...
User's Guide - Page 3
Contents 1. Introduction ...3 2. Safety Notification ...4 3. Hardware Installation 5 4 Web Management Settings 6
4.1. Primary Setup ...7 4.2. System...11 4.3. Operating Mode...12 4.4. Status...14 4.5 Traffic Log...15 4.6 AccessControl ...16 4.7 Advanced Wireless...17 4.8. SNMP...19 4.9. Upgrade Firmware...20
5. Troubleshooting ...22
User's Guide - Page 4
...
1. Introduction
Thank you for purchasing TEW-410APBplus 54Mbps 802.11g Wireless Access Point This user guide will assist you with the installation procedure. The package you have received should contain the following items:
TEW-410APBplus User Guide (CD-ROM) Quick Installation Guide DC Power Adapter and Power cord One Cat5 Cable
Note: if anything is missing, please contact your vendor
User...
User's Guide - Page 5
... placed in a safe and secure location. To ensure proper operation, please keep the unit away from water and other damaging elements. Please read the user manual thoroughly before you install the device. The device should only be repaired by authorized and qualified personnel.
Please do not try to open or repair the...
User's Guide - Page 6
... power adapter may cause damage to your device and
violate your warranty.
Reset
Press the Reset Button for approximately ten seconds, all configurations will set to factory default settings.
LAN
The RJ-45 Ethernet ports used to connect your PC, hub, switch or Ethernet network.
AP Default Settings
The default settings are shown following.
User
admin
Password
admin
AP IP Address...
User's Guide - Page 10
TEW-410APBplus
Important Notice
In order to make right use of WPA, please ensure that your current Wireless Adapter's driver, and Wireless Utility can support it, WPA needs 802.1x authentication (when RADIUS mode is chosen), though the Operating System must also support 802.1x protocol. For Microsoft's OS family, only Windows XP has incorporated this by default. The rest...
User's Guide - Page 13
4.3. Operating Mode
Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations. AP Client: Please input the MAC Address of the remote AP. In this operating mode, the device will be used as wireless NIC.
User's Guide - Page 15
...-flash every 5 seconds to keep most update information. LAN section will be displaying all information related on AP, such as the IP address and the current configuration type. Wireless section will be displaying information related on the Wireless interface, such as SSID, Channel, Encryption and statistics of network traffic. *Click the Refresh button to refresh the AP's status and settings...
User's Guide - Page 16
TEW-410APBplus
4.5 Traffic Log
Traffic Log: The AP can keep logs of all incoming or outgoing traffic for your network traffic. This feature is disabled by default. To keep activity logs, select Enable. To keep a permanent record of activity logs as a file on your PC's hard drive, Log viewer software must be used. In the Send Log...
User's Guide - Page 19
... and 1000. A beacon is a packet broadcast by the AP to synchronize the wireless network. The default value is 100.
Antenna selection: There are 3 types antenna setting for this device. Default setting is Diversity.
RTS Threshold: This value should remain at its default setting of 2346. Should you encounter inconsistent data flow, only minor modifications are recommended...
User's Guide - Page 21
... version has a new feature that you want to use. Note: When you upgrade the AP's firmware, you may lose its configuration settings, so make sure you write down the AP's settings before you upgrade its firmware. To upgrade the AP's firmware: 1. Download the firmware upgrade file from the internet. 2. Extract the firmware upgrade file. 3. Click the Firmware Upgrade button. 4. On the Firmware Upgrade...
User's Guide - Page 22
TEW-410APBplus
5. Double-click the firmware upgrade file. 6. Click the Upgrade button, and follow the on-screen instructions. Note: Do not power off the AP or press the Reset button while the firmware is being upgraded.
User's Guide
21
User's Guide - Page 23
... on the rear of the AP to revert to the default settings.
I can't connect to other computers on my LAN.
Cause: The IP Addresses of the computers are not set correctly. Network cables are not connected properly. Windows network settings are not set correctly.
Resolution: Make sure that each computer has a unique IP Address. And the IP must be in the same subnet as
the...
User's Guide - Page 24
TEW-410APBplus
Wireless Troubleshooting I can't access the Wireless AP from a wireless network card
Cause: Out of range. IP Address is not set correctly.
Resolution: Make sure that the Mode, SSID, Channel and encryption settings are set the same on each
wireless adapter. Make sure that your computer is within range and free from any strong electrical devices that may
cause interference. Check your...
Quick Installation Guide - Page 2
Table of Contents
English ...1 1. Prepare for Installation 1 2. Install Hardware 2 3. Configure the computer's TCP/IP Settings 3 4.Configure the Access Point 8
Troubleshooting 13
Quick Installation Guide - Page 3
...more detailed information from the User's Guide on the CD-ROM. If you need further technical support, please visit www.TRENDNET.com or contact us by phone.
Verify Package Contents
Please make sure you have everything in the box:
TEW-410APBplus
User's Guide CD-ROM
TEW-410APBplus
54Mbps 802.11g Wireless Access Point + Bridge Quick Installation Guide
Guide d'installation rapide pour le Point d'Acc...
Quick Installation Guide - Page 4
... RJ-45 network cable from the Access Point to any port on the Hub or Switch.
2. For Wired PC setup, please connect another RJ-45 network cable from the PC to the same Hub or Switch.
3. Connect the AC Power Adapter to the Access Point and to an available power outlet. Turn on the Access Point.
TEW-410APBplus
POWER
3
2 1
Verify Hardware Installation
Verify...
Quick Installation Guide - Page 5
... computer's TCP/IP Settings
The Access Point has a default IP address 192.168.1.250, therefore to be able to access and configure the Access Point, the computer's TCP/IP settings need to be changed.
Windows 95/98/98SE/ME
1. Find the Start button located on Desktop. 2. Click Start; click Settings and then click on Control Panel. 3. Double-Click the Network...
Quick Installation Guide - Page 6
..., the installation may require files from your Windows
CD-ROM. If this happens insert Windows CD-ROM into your
CD-ROM drive and select the CD-ROM drive to load the necessary files. 8. After the files load, the System Settings Change prompt will appear; click
Yes to restart your computer.
NOTE: If this prompt does not appear, you must manually restart your computer.
9. Your computer is...
Quick Installation Guide - Page 7
Windows 2000/XP
1. Find Start button located on Desktop. 2. Click Start; click Settings and then click on Control Panel. 3. Double-Click the Network Connection Icon. 4. Right-Click on the Local Area Connection icon and then click on
Properties. The Local Area Connection Properties box will appear.
5
English