TRENDnet TE100-S4PCI driver and firmware
Drivers and firmware downloads for this TRENDnet item
Related TRENDnet TE100-S4PCI Manual Pages
Download the free PDF manual for TRENDnet TE100-S4PCI and other TRENDnet manuals at ManualOwl.com
Data Sheet - Page 1
... four network segment connections Port 4 supports MDI-II or MDI-X (push button) PCI bus master memory access for high throughput and low CPU demand Plug and Play installation Half- and full-duplex with auto-negotiation Data forwarding and filtering rate for 10/100Mbps speed Up to 1K active MAC address entry table with selflearning and table-aging 1 MB RAM buffer per device...
Data Sheet - Page 2
...
Certifications: • FCC, CE, VCCI-II
NETWORKING SOLUTIONS
PRODUCT INFORMATION
TE100-S4PCI 4-port 10/100Mbps N-way Ethernet Switch Adapter
To Order Please Call: 1-888-326-6061
ORDERING INFORMATION
TRENDware International, Inc.
3135 Kashiwa Street
Torrance, CA. 90505. USA
Tel: 310-891-1100
R
Fax: 310-891-1111
TRENDnet
Web: www.TRENDNET.com
TRENDware, USA
Email: [email protected]...
Manual - Page 2
... a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause...
Manual - Page 3
Table of Contents
INTRODUCTION 1
ABOUT FAST ETHERNET 1 ABOUT AUTO-NEGOTIATION 2 SWITCHING TECHNOLOGY 4 PRODUCT FEATURES 5
INSTALLATION 7
UNPACK AND INSPECT 7 INSTALL THE ADAPTER 7 LED INDICATORS 8 UPLINK BUTTON 9 SOFTWARE INSTALLATION 9
SPECIFICATIONS 11
Manual - Page 5
... 4 UTP network cabling, but does not provide for full duplex operation. 100Base-TX requires Category 5 cabling, but does provide full duplex operation. Full duplex 100Base-TX operation allows simultaneous transmission and reception; both at 100Mbps, thus providing service potentially equal to 200Mbps full-duplex service.
The 4-Port 10/100M NWay Ethernet Switch Card does not support the 100Base...
Manual - Page 6
... phone line, then you are given the "Connect" message which signals the end of the intermodem negotiation and the beginning of your intended communication with the remote computer.
Auto-negotiation between devices within an Ethernet LAN is similar in concept, but much briefer. The two devices involved in the autonegotiation will be the 4-Port 10/100M NWay Ethernet Switch Card...
Manual - Page 7
...-and-receive). Startup communication between the two devices occurs when devices are power-on, the cable connection between them is good, and the Network Operating System software is running. As soon as those conditions are satisfied, the preparatory process of auto-negotiation between the 4-Port 10/100M NWay Ethernet Switch Card and its supporting hub proceeds automatically. If the hub...
Manual - Page 8
... same network cabling and adapter cards.
For Fast Ethernet Networks, a switch is an effective way of eliminating problems of chaining hubs beyond the "two-repeater limit." A switch can be used to split parts of the network into different collision domains, making it possible to expand your Fast Ethernet Network beyond the 205-meter network diameter limit for 100BASETX networks. Switches supporting...
Manual - Page 9
...; 1K MAC address entry table with self-learning and table-aging • 1 MB RAM buffer per device • LED indicators for Link/Activity, 100Mbps and Collision/Full-
duplex per each port. • Drivers for all leading Network Operating Systems. Software
drivers for:
• Workstation for DOS ODI Client
• Server Driver for NetWare 3.12/4.x
• Client 32 for Windows 95
•...
Manual - Page 10
• LAN Manager Workstation/Server • Windows for Workgroups v3.11 • Windows NT 3.5x & 4.0 • Windows 95, 95/OSR2, 98, 2000 • SCO UNIX 3.X/5.X • Packet Driver
• LANtastic 6.0 with NDIS drive
6
Manual - Page 11
... remove all items. In addition to this User's Guide, ascertain that you have: • One 4-Port 10/100Mbps NWay Ethernet Switch Card • Software Diskette • User's Manual
Install the Adapter
1. Shut down the computer, unplug its power cord, and remove the chassis cover.
2. If your order does not include the Boot ROM option, go ahead to Step 3. If your order...
Manual - Page 12
... edge of the 4-Port 10/100Mbps NWay Ethernet Switch Card into the connector of any available PCI Bus Master expansion slot. Press the card firmly into the connector and ascertain that the card's contacts are fully seated in the connector.
4. Install the bracket screw that secures the card to the computer chassis.
5. Replace the computer's chassis cover.
6. Reconnect the computer's power cord, and...
Manual - Page 13
... switch or a hub to form a network backbone.
Software Installation
On account of the great variety of network environments for which the 4-Port 10/100Mbps NWay Ethernet Switch Card may be used, and revisions of those network systems, the instructions for software installation are given as HELME.COM files on the 4-Port 10/100Mbps NWay Ethernet Switch Card Software Diskette. Run the root directory...