TRENDnet TE100-DX4PCI driver and firmware
Drivers and firmware downloads for this TRENDnet item
Related TRENDnet TE100-DX4PCI Manual Pages
Download the free PDF manual for TRENDnet TE100-DX4PCI and other TRENDnet manuals at ManualOwl.com
Data Sheet - Page 1
...TX technology to give you high-speed and high performance. This network device integrates four 10/100Mbps Fast Ethernet hub ports into a 10/100Mbps PCI Ethernet card. TRENDnet's TE100-DX4PCI allows network transmit/ receive between 10Mbps and 100Mbps Network segments and consists of one 10/100Mbps PCI Fast Ethernet card and four 10/100Mbps hub ports. And, its Plug-and-Play (PnP) function, makes it...
Data Sheet - Page 2
...
TE100-DX4PCI: 4-port Dual Speed Fast Ethernet Hub Card TE100-PCIWplus: 10/100Mbps Fast Ethernet Card for PCI TE100-SK2: Dual Speed Starter Kit
(1 x TE100-DX4PCI, 1 x TE100-PCIWplus and 1 x 15' CAT 5 Cable)
To Order Please Call: 1-888-326-6061
ORDERING INFORMATION
TRENDware International, Inc.
3135 Kashiwa Street
Torrance, CA. 90505. USA
Tel: 310-891-1100
R
Fax: 310-891-1111
TRENDnet...
Manual - Page 2
Ethernet Card forPCI
FCC Compliance Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device...B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. ...
Manual - Page 3
CONTENTS
Ethernet Card for PCI
FCC Compliance Statement 1 Section 1 Introduction 4 Section 2 Installation 5 Section 3 Configuration and Diagnostics .... 6 Section 4 Drivers Installation 7 Section 5 Cable Specifications 8 Section 6 Troubleshooting 9 Section 7 Specifications 10 Section 8 LED Indication 11
3
Manual - Page 4
... Ethernet hub card is a high performance network device that is designed to easily link four 10/100Mbps hub with a 100Mbps PCI interface card. The hub card consists of four (4) 10/100BASE-TX hub port to linking and forwartding packets in one segment, it also includes a 32-bit PCI interface to provide an additional connection with the network segment.
The Ethernet hub card...
Manual - Page 5
... the edge of the connector slot until the card is snugly seated in the expansion slot and fasten the retaining bracket with screw from the slot cover. 6. Reinstall your personal computer's cover and re-connect the power cord and all cables. 7. Connect the Ethernet cable to your personal computer.
Note: System Requirements: A PC and BIOS that support the PCI Local Bus
5
Manual - Page 6
... Your Ethernet hub card has built-in a 100Mbps MAC interface which is automatically configured when you power-up your computer, In certain computers, however, you must modify your BIOS by entering your CMOS SETUP utility. To view the configuration parameters assigned by the BIOS, boot the computer to DOS, insert the diskette into the floppy drive and then execute the utility software...
Manual - Page 7
Ethernet Card for PCI Section 4 Drivers Installation Be sure to install the proper driver for the hub card to provides a connection between the 100Mbps MAC interface and the four 10/100Mbps nodes. You can use the drivers supplied by the software diskette that is compatible with your Networking Operating System. The driver for each Networking Operating System is under a separate directory. Each ...
Manual - Page 9
Ethernet Card for PCI Maximum cable length: 300'(100m)
Section 6 Troubleshooting
This section describes reasons for some adapter's
f
a
i
l
u
r
e
s
and the actions to be taken to resolve the problems.
• PCI scan specified, device not found
Action: Verify that the PCI Ethernet adapter is physically installed properly. Otherwise, install the card in a different PCI slot or replace ...