Sony SLV-495 driver and firmware
Related Sony SLV-495 Manual Pages
Download the free PDF manual for Sony SLV-495 and other Sony manuals at ManualOwl.com
Operating Instructions primary manual - Page 2
... is wider than the other for the purpose of safety and will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, contact your Sony dealer.
• (SLV-495) Unplug the unit from the wall outlet if you do not intend to use it...
Operating Instructions primary manual - Page 9
.../UHF connector and the antenna terminals of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the VCR to...
Operating Instructions primary manual - Page 29
... recording programs.
Before you start...
• Turn on the VCR and the TV. • Set the TV to the VCR channel (channel 3
or 4). If your TV is connected to the VCR using A /V connections, set the TV to video input.
®
.‹)
O
O
.0) CZ).CZ) CZ)
MENU EXECUTE
CURSOR
• Press TV/VTR to display the VTR indicator in the VCR's display window...
Operating Instructions primary manual - Page 35
... to preset, set them directly using manual presetting.
Before you start...
a NEI
• Turn on the VCR and the TV.
• Set the TV to the VCR channel (channel 3 or 4). If your TV is connected to the VCR using A/V connections, set the TV to video input.
• Press TV /VTR to display the VTR indicator in the VCR's display window.
MENU, EXECUTE...
Operating Instructions primary manual - Page 43
... you want to find later, press COUNTER RESET. The counter in the display window resets to "0H00M00S." Search for the point afterwards by referring to the counter.
n 11 11 111H1s
To display the counter on the TV screen, press DISPLAY.
Notes • Tapes recorded in the LP mode on other VCRs can be played back on...
Operating Instructions primary manual - Page 45
... display window.
VTR
SP
I- I I
I II
4
• CH
a
Press CH +/- to select the channel you want to record.
VTR
SP
irtt ti 1ti3
5
TAPE
SPEED
CD
6 •REC
Press TAPE SPEED to select the tape speed, SP or EP.
EP provides recording time three times as long as SP, however, SP produces better picture and audio...
Operating Instructions primary manual - Page 46
Recording TV programs (continued)
To watch another TV program while recording
1 Press TV/VTR to turn off the VTR indicator in the display window. 2 If the TV is connected to the VCR's LINE OUT jacks, set the TV to TV
input; if not, skip this step.
3 Select another channel on the TV.
To save a recording
To prevent accidental erasure, break off the safety tab...
Operating Instructions primary manual - Page 49
... VCR is recording: • Reset the counter. • Display tape information on the TV screen. • Check the timer settings. • Watch another TV program.
To lock the VCR after setting the timer (Child Lock) Hold down POWER on the VCR until the VCR beeps. The VCR turns off and the O-ri indicator appears in the display window. The...
Operating Instructions primary manual - Page 55
... adjusts the tracking when playing a tape
(the tracking indicator by4 flashes in the display window, then goes off),
distortion may occur if the tape was recorded in poor condition. In this case, manually adjust the tracking.
Press the TRACKING +/- buttons on the VCR to display the tracking meter. The distortion should disappear as you press one...
Operating Instructions primary manual - Page 58
Editing with another VCR (continued)
Operation (when recording on this VCR)
Before you start editing
• Turn on your TV and set it to the
video channel.
• Press INPUT SELECT on the remote
@
commander to display "Ll" or "L2" in
the display window.
• Press TAPE SPEED on the remote
commander to select the tape speed,
SP or...
Operating Instructions primary manual - Page 61
... has stopped and o "-:- -" lights in the display
.(-) window.
• The clock stops if the VCR is disconnected from the wall outlet for more than one hour. Reset the clock
(and timer).
The playback picture does not appear on the TV screen.
• Make sure the TV is set to the channel for the VCR. If...
Operating Instructions primary manual - Page 65
Display window
3
5 6
7
TIMER Ell3IVTR 1
••• I/
SP
EP
LP
10
[11 TIMER indicator (48, 51) 121 REC (recording) indicator
rdl VTR indicator (46)
(Child Lock) indicator (49) 0 ...a
AC power cord
rfl LINE-1 IN AUDIO/VIDEO jacks
(22, 57)
3 VHF/UHF IN/OUT connectors (10, 13, 16, 19, 22, 24)
RF UNIT switch (59)
151 LINE OUT AUDIO/VIDEO jacks (8) 161 CABLE BOX CONTROL CTRL S
...
Operating Instructions primary manual - Page 68
... the display window.
To record a program
1 Press VCR Plus+ on the remote commander.
2 Enter the program's PlusCode number.
3 Select ONCE, DAILY, or WEEKLY, then press SET.
4 Insert a tape. 5 Press POWER to turn off
the VCR.
To watch TV
1 Turn off the VCR, or press the VCR's TV/VTR button until the VTR indicator in the display window goes off.
2 Set the TV...