LevelOne IES-0910 driver and firmware
Related LevelOne IES-0910 Manual Pages
Download the free PDF manual for LevelOne IES-0910 and other LevelOne manuals at ManualOwl.com
Datasheet - Page 2
... - 150Hz, Amplitude 0.35mm (Operation/Storage/Transport) IEC60068-2-27 Ea (Shock) 25g @ 11ms (Half-Sine Shock Pulse; Operation) 50g @ 11ms (Half-Sine Shock Pulse; Storage/Transport) IEC60068-2-32 Ed (Free Fall) 1M (3.281ft.)
Order Information
- IES-0910 8 FE + 1 MM SC Unmanaged Switch -20 to 60, DIN-rail
Package Contents
IES-0910 Quick Installation Guide
www.level1.com one world_one...
Manual - Page 2
... full wire speed switching technology. This switch brings the answer to complicated hardened networking environments.
To get the most out of this manual, you should have an understanding of Ethernet networking concepts.
In this manual, you will find:
· Features on the switch · Illustrative LED functions · Installation instructions · Specifications
IES-0910 User Manual
Page 2
Manual - Page 3
Table of Contents
PREFACE ...2
PRODUCT OVERVIEW ...4 HARDENED ETHERNET SWITCH ...4 PACKAGE CONTENTS ...4 PRODUCT HIGHLIGHTS...5 FRONT PANEL DISPLAY...6
INSTALLATION...7 SELECTING A SITE FOR THE SWITCH...7 DIN RAIL MOUNTING ...8 CONNECTING TO POWER...9 CONNECTING TO YOUR NETWORK ...11
SPECIFICATIONS...12
APPENDIX A - CONNECTOR PINOUTS...13
IES-0910 User Manual
Page 3
Manual - Page 4
... Ethernet Switch
Package Contents
When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller.
· IES-0910 8 FE + 1 MM SC Unmanaged Switch -20 to 60, DIN-rail
· Quick Installation Guide · CD User Manual
IES-0910 User Manual...
Manual - Page 5
... bits memory buffer. · Alarms for power failure by relay output. · Operating voltage and Max. current consumption: 1.1A @ 12VDC, 0.55A @ 24VDC. · Power consumption: 13.2W Max. · Power Supply: Redundant DC Terminal Block power inputs or 12VDC DC JACK with
100-240VAC external power supply. · Supports DIN-Rail, Panel, or Rack Mounting installation.
IES-0910 User Manual
Page...
Manual - Page 7
...-step instructions about how to install the switch:
Selecting a Site for the Switch
As with any electric device, you...devices should not exceed the electromagnetic field (RFC)
standards. · Make sure that the switch receives adequate ventilation. Do not block the ventilation
holes on each side of the switch · The power outlet should be within 1.8 meters of the switch.
IES-0910 User Manual...
Manual - Page 8
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the switch. Installation: Place the switch on the DIN rail from above using the slot. Push the front of the switch toward the mounting surface until it audibly snaps into place. Removal: Pull out the lower edge and then remove the switch from the DIN rail.
IES-0910 User Manual
Page 8
Manual - Page 11
... cross-over cable.
Step 3: Consult the previous section for cabling requirements based on connectors and speed.
Step 4: Connect one end of the cable to the switch and the other end to a desired device.
Step 5: Once the connections between two end devices are made successfully, turn on the power and the switch is operational.
IES-0910 User Manual
Page 11
Quick Install Guide - Page 1
...Installation Guide
Overview
LevelOne IES-0910 Industry Ethernet Switch provides 8 ports of 10/100Base-TX Ethernet plus 1 port 100FX Multimode SC fiber to enable high speed network at mission-critical environment. This device... Single
mode SC type. Support 2048 MAC addresses. Provides 768K bits memory buffer. Alarms for power failure by relay output. Operating voltage and ...