Edimax EU-4230 driver and firmware
Related Edimax EU-4230 Manual Pages
Download the free PDF manual for Edimax EU-4230 and other Edimax manuals at ManualOwl.com
Datasheet - Page 1
... case to add an internal network card. The EU-4207 is also backward compatible with the USB 1.1 specification. Featuring plugand-play, this USB/Ethernet adapter requires no complicated installing procedures. EU-4230 can likewise seamlessly function under Microsoft Windows 2000, 2003, XP, Vista, and Mac OS 10.3 ,10.4, 10.5 or above.
Dual Power Mode There is one upstream port that connects to the PC...
Datasheet - Page 2
...-T/Fast Ethernet 100BaseTX port) Complies with the Full-duplex with flow control and Half duplex with backpressure operation
POWER ON Ethernet connection
POWER Bus-powered : 5V 500mA Self-powered : 5V 2.5A Optional Adapter: Input : 100~240V 50Hz ~60Hz Output : 5V/2.5A
WEIGHT 48g
SYSTEM REQUIRMENTS
CPU: Pentium 233MHz above or MAC Memory size: min. of 64MB RAM One available USB slot Windows 2000...
Quick Install Guide - Page 2
... purchased and the setup screen may appear slightly different from those shown in this QIG. For more detailed information about this product, please refer to the User's Manual on the CD-ROM. The software and specifications are subject to change without notice. Please visit our web site www.edimax.com for the update. All right reserved...
Quick Install Guide - Page 3
...mode z Supports Window 2000/XP/Server 2003/Vista and MAC OS 10.4.x and
above
3. Package Contents
z USB2.0 to Fast Ethernet Adapter with 3-Port USB Hub x1 z Power Adapter x1 z Quick Installation Guide x1 z CD (Driver & Multi-language Quick Installation Guide & User Manual) x1
4. System Requirements
z CPU : Pentium III 1G above or similar z Memory size : 256MB RAM z One CD-ROM drive z Hard Disk : At...
Quick Install Guide - Page 4
5. Hardware Connection
General instructions for installing the USB 2.0 3 Port Hub with Ethernet Adapter are provided below. Since the design of system may vary, refer to your system's reference manual for further information, if needed.
3
Quick Install Guide - Page 5
6. Driver Installation
Windows 2000/XP/Server 2003/Vista
1. With your computer switched on, insert the "USB2.0 to Fast Ethernet Adapter with 3-Port USB Hub" into an available USB2.0 port of your computer. The following message will appear on your screen, Please click 'Cancel' and use the wizard to install driver.
4
Quick Install Guide - Page 6
2. Please insert the installation CD into your CDROM drive. The Autorun setup programs should run under Windows 2000/XP/Server 2003/Vista, or you can click on the "Browse CD" to find other OS drivers in the CD.
3. Connect the Ethernet adapter's USB end to a free USB port of your computer. Then a pop-up message will appear in the notification area indicating the installation is complete.
5
Quick Install Guide - Page 7
... Installation to install the software and then
Reboot the Mac. 6. Connect the Ethernet adapter to a free USB port. Then a New port
Detected screen will prompted, and you will find that a new Ethernet network interface is available.
Connecting to Your Network Now the installation is complete. You can connect the adapter to your network device such as hub, switch or router by an Ethernet cable...
Quick Install Guide - Page 8
... Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not...
Manual - Page 2
... purchased and the setup screen may appear slightly different from those shown in this QIG. For more detailed information about this product, please refer to the User's Manual on the CD-ROM. The software and specifications are subject to change without notice. Please visit our web site www.edimax.com for the update. All right reserved...
Manual - Page 3
Table of Contents
1. Introduction 1 Features 1 Package Contents 1 System Requirements 1
2. Installation 2 Hardware Connection 2 Driver Installation 3 On Windows 2000/XP/Server 2003/Vista 3 On MAC OS X 10.3/10.4 6 Verifying the Driver Installation 10 On windows 2000/XP/Server 2003/Vista 10 On MAC OS X 10.3/10.4 11
3. Specifications 12 4. Federal Communication Commission 13 5. CE Mark ...
Manual - Page 4
...self-power mode z Supports Window 2000/XP/Server 2003/Vista and MAC OS 10.4.x and
above
Package Contents
z USB2.0 to Fast Ethernet Adapter with 3-Port USB Hub x1 z Power Adapter x1 z Quick Installation Guide x1 z CD (Driver & Multi-language Quick Installation Guide & User Manual)
x1
System Requirements
z CPU : Pentium III 1G above or similar z Memory size : 256MB RAM z One CD-ROM drive z Hard Disk...
Manual - Page 5
2. Installation
Hardware Connection
General instructions for installing the USB 2.0 3 Port Hub with Ethernet Adapter are provided below. Since the design of system may vary, refer to your system's reference manual for further information, if needed.
2
Manual - Page 6
Driver Installation On Windows 2000/XP/Server 2003/Vista
1. With your computer switched on, insert the "USB2.0 to Fast Ethernet Adapter with 3-Port USB Hub" into an available USB2.0 port of your computer. The following message will appear on your screen, Please click 'Cancel' and use the wizard to install driver.
3
Manual - Page 7
2. Please insert the installation CD into your CDROM drive. The Autorun setup programs should run under Windows 2000/XP/Server 2003/Vista, or you can click on the "Browse CD" to find other OS drivers in the CD.
3. Connect the Ethernet adapter's USB end to a free USB port of your computer. Then a pop-up message will appear in the notification area indicating the installation is complete.
4
Manual - Page 8
... Vista and might vary slightly for each operation system. Now the installation is complete. You can connect the adapter to a network device by an Ethernet cable:
1. Connect an Ethernet cable to the Ethernet port on the adapter.
2. Connect the other end of the Ethernet cable to your network hub, switch or router.
The Link LED should light up green to indicate a proper physical connection between...
Manual - Page 9
On MAC OS X 10.3/10.4
1. Insert the provided driver CD into your CD-ROM drive. Double-click the CD and navigate to the directory of \Drivers\Mac10.x.\ AX88772.pkg
2. When the Install AX88772 USB CDC Drivers screen appears, please select Continue.
3. When the screen below appears, please choose the volume that you want to install and click Continue.
6
Manual - Page 10
4. When the screen below appears, please click Upgrade to perform the software.
5. Please enter your password as prompted.
6. Please select Continue Installation to install the software when the screen below prompted. 7
Manual - Page 12
... system. These screen shots are from MAC OS X 10.4 and might vary slightly for each operation system. Now the installation is complete. You can connect the adapter to a network device by an Ethernet cable: 1. Connect an Ethernet cable to the Ethernet port on the adapter. 2. Connect the other end of the Ethernet cable to your network hub, switch or router. The Link LED should light up...
Manual - Page 13
.... On Windows 2000/2003/XP: Right-click My Computer on the desktop and click Properties > (Hardware) > Device Manager. In the Network adapters group, an item named ASIX AX88772 USB2.0 to Fast Ethernet Adapter should be displayed. If there is a question or exclamation mark next to that item, then the driver is not properly installed. Please delete the item, select the Delete the driver software for...