Asus PU-DLS - Motherboard - Extended ATX driver and firmware
Drivers and firmware downloads for this Asus item
Related Asus PU-DLS Manual Pages
Download the free PDF manual for Asus PU-DLS and other Asus manuals at ManualOwl.com
PU-DLS User Manual - Page 19
... and components are based on the following high-level goals: support for Plug-and-Play compatibility and power management for configuring and managing all system components, 32-bit device drivers, and installation procedures for Windows NT/2000/XP. Color-coded connectors and descriptive icons make identification easy as required by the PC '99 specification.
ASUS PU-DLS motherboard user guide
1-5
PU-DLS User Manual - Page 20
... of the PU-DLS motherboard as pointed out in the picture on page 1-7.
1. SSI-type power connector 2. DDR DIMM sockets 3. Intel® E7501 northbridge 4. Intel® P64H2 PCI-X Hub 5. 604-pin CPU sockets 6. 8-pin 12V SSI power connector 7. SCSI connector (optional) 8. Adaptec 7902W SCSI controller 9. Firmware hub (FWH) 10. IDE connectors 11. Standby power LED 12. SCSI connector 13. ASUS ASIC 14...
PU-DLS User Manual - Page 37
...Configuring an expansion card
After installing the expansion card, configure the it by adjusting the software settings.
1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page. 3. Install the software drivers for the expansion card.
ASUS PU-DLS motherboard user guide
2-11
PU-DLS User Manual - Page 59
... computer from the floppy disk.
BIOS setup must specify "Floppy" as the first item in the boot sequence.
4. In DOS mode, type A:\AFLASH to run AFLASH.
If the word "unknown" appears after Flash Memory:, the memory chip is either not programmable or is not supported by the ACPI BIOS and therefore, cannot be programmed by the Flash Memory Writer utility.
ASUS PU-DLS motherboard user guide...
PU-DLS User Manual - Page 63
... may want to enable the security password feature or make changes to the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the FWH.
The FWH on the motherboard stores the Setup utility. When you start up the...
PU-DLS User Manual - Page 81
... time updated even when the computer enters suspend mode. In Windows 3.x and Windows 95, you need to install Windows with the APM feature. In Windows 98 or later, APM is automatically installed as indicated by a battery and power cord icon labeled "Power Management" in the Control Panel. Select the item "Advanced" in the Power Management Properties dialog box.
ASUS PU-DLS motherboard user guide...
PU-DLS User Manual - Page 93
....EXE from the BIN folder. Double-click the ASSETUP.EXE to run the CD.
5.1.1 Drivers
This screen displays the drivers available for the onboard devices. Follow the installation wizards or find additional instructions as text files in each of the driver folders.
5.1.2 Management Sofware
This screen displays the ASUS proprietary server management software.
ASUS PU-DLS motherboard user guide
5-1
PU-DLS User Manual - Page 95
... have the driver for the SCSI controllers. You must load the driver manually prior to Windows NT 4.0 installation.
A. Preparing an Adaptec Ultra320 FMS driver disk
A1. Using the Drivers menu in the support CD
1. Insert a blank formatted high density floppy disk into the floppy drive. 2. Place the support CD into the CD-ROM drive. The Drivers menu
appears displaying the available drivers. 3. Click...
PU-DLS User Manual - Page 104
... installation
Windows 2000 does not have the driver for the SCSI controller. You must load the driver manually prior to Windows 2000 installation.
A. Preparing an Adaptec Ultra320 FMS driver disk
A1. Using the Drivers menu in the support CD
1. Insert a blank formatted high density floppy disk into the floppy drive. 2. Place the support CD into the CD-ROM drive. The Drivers menu
appears displaying...
PU-DLS User Manual - Page 105
... Ultra320 FMS driver disk when the setup prompts
you to insert the manufacturer supplied disk into drive A, and press Enter. 5. The screen displays the adapter drivers supported on the disk. Select "Adaptec Ultra320 SCSI Cards (Win2000)" and continue with the rest of the Windows 2000 installation. 6. Your system will reboot once more to finish setting up Windows 2000.
C. Installing the Adaptec...
PU-DLS User Manual - Page 106
... driver under Windows 2000
Follow these instructions only if Windows 2000 is already installed.
1. Right-click on My Computer and choose Properties from the menu. Click on the Hardware tab and click on the Device Manager button.
2. Under SCSI and RAID controllers, click on the "+" sign (on the left) to display the current SCSI adapters installed. Right-click on the device that you wish to update...
PU-DLS User Manual - Page 110
... Driver on an Existing System Installation
You may update the LAN driver directly from the support CD. 1. Insert the support CD into the CD-ROM drive. On the screen that
appears, click on Intel PRO/1000 LAN Driver, then on the item Install Base Driver Only. 2. Follow the screen instructions to complete the driver update.
When done, your Computer Management window shows the installed LAN adapters...
PU-DLS User Manual - Page 112
... Ethernet Controller, then click the right mouse button and select Properties.
6. Select the Driver tab and click on Update Drivers. 7. Click Next. Select Display a list of the known drivers for this device ... 8. Select Network adapters under Hardware Type, and click Next. 9. Click Have Disk..., then insert the LAN driver disk. 10. Follow the succeeding instructions to complete the installation...
PU-DLS User Manual - Page 113
...
Windows 2000 system can automatically recognize the ATI RAGE XL PCI driver during system installation. You do not need to load any driver for supporting the onboard ATI RAGE XL graphics controller chipset.
5.3.4 Enabling ATA100 Feature in Windows® 2000
To enable the ATA100 feature under Windows 2000, you need to upgrade to Windows 2000 Service Pack 2.
ASUS PU-DLS motherboard user guide...
PU-DLS User Manual - Page 114
...not have the driver for the SCSI controller. You must load the driver manually prior to Windows XP installation.
A. Preparing an Adaptec Ultra320 FMS driver disk
A1. Using the Drivers menu in the support CD
1. Insert a blank formatted high density floppy disk into the floppy drive. 2. Place the support CD into the CD-ROM drive. The Drivers menu
appears displaying the available drivers. 3. Click on...
PU-DLS User Manual - Page 116
... FMS driver disk when the setup prompts you to insert the manufacturer supplied disk into drive A, and then continue.
5. The screen displays the adapter drivers supported on the disk. Select Adaptec Ultra320 SCSI Cards (WinXP IA64) and press Enter. Continue with the rest of the Windows installation.
6. Your system will reboot once more to finish setting up the operating system.
D. Updating the...
PU-DLS User Manual - Page 119
...
You may update the LAN driver directly from the support CD. 1. Insert the support CD into the CD-ROM drive. On the screen that
appears, click on Intel PRO/1000 LAN Driver, then on the item Install Base Driver Only. 2. Follow the screen instructions to complete the driver update.
When done, your Computer Management window shows the installed LAN adapters.
ASUS PU-DLS motherboard user guide
5-27
PU-DLS User Manual - Page 121
... mouse button and select Properties.
6. Select the Driver tab and click on Update Drivers. 7. Click Next. Select Display a list of the known drivers for this device ... 8. Select Network adapters under Hardware Type, and click Next. 9. Click Have Disk..., then insert the LAN driver disk. 10. Follow the succeeding instructions to complete the installation.
ASUS PU-DLS motherboard user guide
5-29
PU-DLS User Manual - Page 131
... parameters. By default, the driver automatically detects the line speed and duplex mode. If you want to force any of these settings, choose 'Advanced Options' and set the speed and duplex modes. Exit'netconfig' and choose to relink the kernel.
5. Reboot the system.At the command prompt, type:
# reboot (or init 6)
ASUS PU-DLS motherboard user guide
5-39
PU-DLS User Manual - Page 133
... is not supplying patches against the kernel source†to allow for static linking of the driver. For questions related to hardware requirements, refer to the documentation supplied with your Intel PRO/1000 adapter. All hardware requirements listed apply to use with Linux. New features include support for the Intel PRO/1000 desktop adapter.
ASUS PU-DLS motherboard user guide
5-41