TP-Link TL-SL5428E driver and firmware
Drivers and firmware downloads for this TP-Link item
Related TP-Link TL-SL5428E Manual Pages
Download the free PDF manual for TP-Link TL-SL5428E and other TP-Link manuals at ManualOwl.com
Quick Installation Guide - Page 18
... the IP address can be set as 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.0. 3) Try another port on the Switch and make sure the cable is the right type. 4) Turn off the power. After a while, turn on the power again.
What can I do if I could not access the Internet?
Make...
User Guide - Page 8
... Commands 112
system-descript ...112 ip address...112 ip dhcp-alloc ...113 ip bootp-alloc ...113 reset ...114 reboot ...114 user-config backup ...115 user-config load...115 user-config save ...116 firmware upgrade ...116 ping ...117 tracert ...117 loopback ...118 show system-info...119 show ip address ...119
Chapter 22 Ethernet Configuration Commands 120
VII
User Guide - Page 128
TL-SL5428E 24-port 10/100Mbps + 4-port Gigabit L2 Managed Switch CLI Guide ip-addr -- IP Address of the TFTP server.
Command Mode
Privileged EXEC Mode
Example
Download the configuration file to the switch by TFTP server with the IP 192.168.0.148 and name this file config.cfg: TP-LINK# user-config load filename config.cfg ip-address 192.168.0.148...
User Guide - Page 129
TL-SL5428E 24-port 10/100Mbps + 4-port Gigabit L2 Managed Switch CLI Guide
Example
Upgrade the switch system via the TFTP server with the IP 192.168.0.148: TP-LINK# firmware upgrade filename firmware.bin ip-address 192.168.0.148
ping
Description
The ping command is used to test the connectivity between the switch and one node of the network... the network device is failed to establish: TP-LINK# ping...
User Guide - Page 4
6.3.2 Config Backup 26 6.3.3 Firmware Upgrade 27 6.3.4 System Reboot 28 6.3.5 System Reset 28 6.4 Access Security ...28 6.4.1 Access Control 28 6.4.2 SSL Config ...30 6.4.3 SSH Config ...31 Chapter 7 Switching...37 7.1 Port ...37 7.1.1 Port Config ...37 7.1.2 Port Mirror ...38 7.1.3 Port Security ...40 7.2 LAG ...41 7.2.1 LAG Table ...42 7.2.2 Static LAG ...43 7.2.3 LACP Config ...44 7.3 ...
User Guide - Page 13
... the cable connected to
the switch. z Loopback: Test if the port of the switch and the connected device
are available. z Network Diagnose: Test if the destination is reachable and the
account of router hops from the switch to the destination.
Introduces how to download firmware of the switch via FTP function.
Lists the glossary used in this manual...
User Guide - Page 34
...implemented on Config Restore, Config Backup, Firmware Upgrade, System Reboot and System Reset pages.
...power down the switch while being restored. 3. After being restored, the current settings of the switch will be lost. Wrong uploaded
configuration file may cause the switch unmanaged.
6.3.2 Config Backup
On this page you can download the current configuration and save it as a file to your computer...
User Guide - Page 35
... via the Web management page. To upgrade the system is to get more functions and better performance. Go to http://www.tp-link.com to download the updated firmware. Choose the menu System→System Tools→Firmware Upgrade to load the following page.
Figure 6-11 Firmware Upgrade
Note: 1. Don't interrupt the upgrade. 2. Please select the proper software version matching with your hardware to...
User Guide - Page 40
...remote management being leaked.
Comprising server and client, SSH has two versions, V1 and V2 which are not compatible with each other. In the communication, SSH server and client can auto-negotiate the SSH version... supports SSH server and you can log on to the switch via SSH connection using SSH client software.
SSH key can be downloaded into the switch. If the key is successfully downloaded,...
User Guide - Page 41
....
Application Example 1 for SSH:
¾ Network Requirements
1. Log on to the switch via password authentication using SSH and the SSH function is enabled on the switch.
2. PuTTY client software is recommended.
¾ Configuration Procedure
1. Open the software to log on to the interface of PuTTY. Enter the IP address of the switch into Host Name...
User Guide - Page 43
3. On the Web management page of the switch, download the public key file saved in the computer to the switch.
Note: 1. The key type should accord with the type of the key file. 2. The SSH key downloading can not be interrupted. 4. Download the private key file to SSH client software.
35
User Guide - Page 179
... Global Config, Port Config and Radius Server pages.
13.5.1 Global Config
On this page, you can enable the 802.1X authentication function globally and control the authentication process by specifying the Authentication Method, Guest VLAN and various Timers. Choose the menu Network Security→802.1X→Global Config to load the following page...
User Guide - Page 183
... an authentication Required. Record the information of the client in the LAN to
server to the switch and do the authentication server and configure the corresponding
some configuration.
authentication username and password for the client.
2 Install the 802.1X client Required. For the client computers, you are required to
software.
install the 802.1X software TpSupplicant provided on...
User Guide - Page 225
... not provided. If necessary, please download it on the Internet.
16.2.4 Backup Log
Backup Log feature enables the system logs saved in the switch to be output as a file for device diagnosis and statistics analysis. When a critical error results in the breakdown of the system, you can export the logs to get some related...
User Guide - Page 230
... a common protocol used in the IP network for files transfer. If there is something wrong with the firmware of the switch and the switch can not be launched, the firmware can be downloaded to the switch again via FTP function.
1. Hardware Installation
Figure 16-1 1） Connect FTP server to port 1 of the switch. 2） Connect the...
User Guide - Page 232
... following Figure 16-5.
Configure Bits per second as 38400, Data bits as 8, Parity as None, Stop bits as 1, Flow control as None, and then click OK.
Figure 16-5 Port Settings
3. Download Firmware via bootrom menu
To download firmware to the switch via FTP function, you need to enter into the bootrom menu of the switch and take...
User Guide - Page 233
... can only use the port 1 to upgrade" will display in the hyper terminal shown as the following figure.
6） When the prompt "Are you want to upgrade the firmware[Y/N]:" displays, please enter Y to start upgrade or enter N to quit upgrade shown as the following figure. The # icon indicates it is upgrading. After upgrading, the [TP-LINK] command will display.
7） Please enter start...
User Guide - Page 242
... version on your computer, the 802.1X Client Software TpSupplicant can not work. It's recommended to go to http://www.winpcap.org to download the latest version of WinPcap for installation.
1.2 Uninstall Software
If you want to remove the TpSupplicant, please take the following steps: 1. On the Windows taskbar, click the Start button, point to All ProgramsÆTP-LINK...
User Guide - Page 246
... does this error dialog box pop up when starting up the TP-LINK 802.1X Client Software?
A1: It's because the supported DLL file is missing. You are suggested to go to http://www.winpcap.org to download WinPcap 4.0.2 or the higher version for installation, and run the client software again.
Q2: Is this TP-LINK 802.1X Client Software compliable with...
User Guide - Page 250
... Management Protocol (SNMP) The application protocol in the Internet suite of protocols which offers network management services. Simple Network Time Protocol (SNTP) SNTP allows a device to set its internal clock based on periodic updates from a Network Time Protocol (NTP) server. Updates can be requested from a specific NTP server, or can be received via broadcasts sent by NTP servers. Spanning...