Seagate ST4000DM000 driver and firmware
Related Seagate ST4000DM000 Manual Pages
Download the free PDF manual for Seagate ST4000DM000 and other Seagate manuals at ManualOwl.com
Product Manual - Page 2
... countries. Barracuda, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and...their respective owners.
One gigabyte, or GB, equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. Quantitative usage examples for ...
Product Manual - Page 7
... transfer capability without local processor intervention. • Quiet operation. • 300 Gs nonoperating shock. • SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns. • Support for S.M.A.R.T. drive monitoring and reporting. • Supports latching SATA cables and connectors.
Barracuda 7200.8 Serial ATA Product Manual, Rev. F
1
Product Manual - Page 8
... environment to host software where two devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment.
The Serial ATA host adapter and drive share the function...
Product Manual - Page 24
... to access the following web page: www.seagate.com/support/service/ From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
None required.
18
Barracuda 7200.8 Serial ATA Product Manual, Rev. F
Product Manual - Page 26
... (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and used...
Product Manual - Page 27
...components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,... materials near circuitry with sulfide-free alternatives.
Barracuda 7200.8 Serial ATA Product Manual, Rev. F
21
Product Manual - Page 29
... computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.
Barracuda 7200.8 Serial ATA...
Product Manual - Page 30
... are Device 0 (master) devices.
Serial ATA drives are designed for easy installation with no jumpers, terminators, or other settings. It is not necessary to set any jumpers on this drive for proper operation. The jumper block adjacent to the signal connector is for factory use only.
SATA Signal
Jumper Block (factory use only)
SATA Power
Figure 3. Serial ATA connectors
3.3
Serial ATA cables...
Product Manual - Page 33
4.0 Serial ATA (SATA) interface
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0-4; multiword DMA modes 0-2, and Ultra DMA modes 0-6.
For detailed information about the Serial ATA interface, refer to the "Serial ATA: High Speed Serialized AT Attachment" specification.
4.1
Hot-Plug compatibility
...
Product Manual - Page 34
4.2
Serial ATA device plug connector pin definitions
Table 7 summarizes the signals on the Serial ATA interface and power connectors..
Table 7: Serial ATA connector pin definitions
Segment Pin
S1
S2
S3
...Ground
2nd mate
P7
V5
Power P8
V5
P9
V5
P10 Ground
5V power, pre-charge, 2nd mate 5V power 5V power 2nd mate
P11 Ground or LED signal If grounded, drive does not use deferred spin...
Product Manual - Page 35
...refer to the Serial ATA: High Speed Serialized AT Attachment specification. See "S.M.A.R.T. commands" on page 35.for details and subcommands used in the S.M.A.R.T. implementation.
Table 8: Supported ATA commands
Command name Check Power Mode Device Configuration Freeze Lock Device Configuration Identify Device Configuration Restore Device Configuration Set Device Reset Download Microcode Execute...
Product Manual - Page 37
... settings.
The following commands contain drive-specific features that may not be included in the Serial ATA specification.
Word
0
1 2 3 4 5 6 7-9 10-19 20 21 22 23-26
27-46
47
48 49 50 51 52 53 54 55 56 57-58
Description Configuration information: • Bit 15: 0 = ATA; 1 = ATAPI • Bit 7: removable media • Bit 6: removable controller...
Product Manual - Page 40
...
This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read...
Product Manual - Page 41
... ATA-5 Standard.
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:
http://seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to...
Product Manual - Page 45
..., write 4, 6, 8
B
bels 5, 7, 9 BPI 4, 6, 8 buffer 4, 6, 8, 11 Bytes per sector 4, 6, 8, 10
C
cables and connectors 24
Cache 4, 6, 8, 11
capacity 10 case temperature 16 CE mark 19 certification 19 Check Power Mode 29 Class B computing device 20 compatibility 19 Conducted noise 15 Conducted RF immunity 18 Configuring the drive 23 connectors 24 Corrosive environment 21 CSA C22.2 (950) 19...