HP 200-240V driver and firmware
Related HP 200-240V Manual Pages
Download the free PDF manual for HP 200-240V and other HP manuals at ManualOwl.com
HP 30-A Power Distribution Unit Installation Instructions - Page 1
... kit)
Important safety information
Before installation, read the Important Safety Information on the HP website (http://www.hp.com/support/importantsafetyinformation).
© Copyright 2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements...
HP 30-A Power Distribution Unit Installation Instructions - Page 2
...as the line voltage of the main AC circuit feeding the PDU.
• Be sure that the load products being connected to the PDU are adjusted for, or are otherwise capable of, operating from this...damage.
• Be sure the power source receptacle is installed near the rack and is easily accessible so that the plug on the PDU power supply cord can serve as the disconnect device for the rack.
• ...
HP 30-A Power Distribution Unit Installation Instructions - Page 3
... the PDU.
2. Install two M5 barrel nuts...power cord grounding plug. The grounding plug is an important safety feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
5. Plug the PDU power cord (3) into the appropriate power outlet.
Installation...
HP 30-A Power Distribution Unit Installation Instructions - Page 4
... the PDU. 2. Install four cage nuts where...power cord grounding plug. The grounding plug is an important safety feature. • Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. • Unplug the power cord from the power supply to disconnect power to the equipment.
4. Plug the PDU power cord (2) into the appropriate power outlet.
Installation...
HP Basic Power Distribution Unit Installation Guide - Page 1
HP Basic Power Distribution Unit Installation Guide
Abstract
This document is for the person who installs and maintains HP PDU products. HP assumes you are qualified in the installation of electrical equipment and trained in recognizing hazards in products with hazardous energy levels.
Part Number: 720595-002 May 2013 Edition: 2
HP Basic Power Distribution Unit Installation Guide - Page 3
...
Before you begin ...4
Overview ...4 Safety and regulatory compliance...4 Important safety information ...4 Required tools ...5 Additional requirements ...5
Recommended hardware configurations 6
Configurations ...6
Hardware installation ...9
Installing the PDU ...9 Installing 1U and 0U PDUs ...13 Securing the cables ...16
Acronyms and abbreviations...17 Documentation feedback ...18
Contents 3
HP Basic Power Distribution Unit Installation Guide - Page 4
...
This document provides installation instructions for qualified personnel for installing an HP Basic PDU.
Safety and regulatory compliance
For safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at the HP website (http://www.hp.com/support/Safety-Compliance-EnterpriseProducts).
Important...
HP Basic Power Distribution Unit Installation Guide - Page 5
... current through the ground conductor exceeds 5% of the input current per line under normal operating conditions, the system loads should be divided among multiple power connections.
Required tools
The following tools are required for installation:
• Phillips screwdriver • Torx screwdriver
Additional requirements
If your facility or configuration requires an L5-20R plug...
HP Basic Power Distribution Unit Installation Guide - Page 6
Recommended hardware configurations
Configurations
The PDU is installed in a rack in the following configurations:
• A single PDU configuration, with the outlets facing the center of the rack
• A single PDU configuration, with the outlets facing the rear of the rack
Recommended hardware configurations 6
HP Basic Power Distribution Unit Installation Guide - Page 9
Hardware installation
Installing the PDU
1. Align and install the power cord retention bracket with the screw holes marked "C."
2. Align and install the mounting pins with the screw holes marked "M."
Hardware installation 9
HP Basic Power Distribution Unit Installation Guide - Page 10
3. If installing the PDU inverted, install a mounting pin on the bottom of the PDU. 4. If needed, install the input power cable retention band.
Hardware installation 10
HP Basic Power Distribution Unit Installation Guide - Page 11
5. If needed, insert and secure the power cable.
6. Install the PDU and ensure the mounting pins are engaged with the rack.
CAUTION: When moving a rack with installed components, always use the shipping bracket to secure the PDU.
Hardware installation 11
HP Basic Power Distribution Unit Installation Guide - Page 12
7. If the PDU is not inverted, install the shipping bracket above the PDU. 8. If the PDU is installed above 39U, flip the PDU shipping bracket to allow space for the rack shipping
bracket.
Hardware installation 12
HP Basic Power Distribution Unit Installation Guide - Page 13
9. If the PDU is inverted, install the shipping bracket over the mounting pin below the PDU.
Installing 1U and 0U PDUs
1. Attach the power cord retention bracket.
Hardware installation 13
HP Basic Power Distribution Unit Installation Guide - Page 14
2. Attach the appropriate mounting brackets. Each bracket only requires two screws per side for this product. o 1U bracket installation
o 0U bracket installation
3. Install cage nuts.
Hardware installation 14